How to Remove Carpet: Steps, Tools and What You Will Find Underneath

To remove carpet, cut it into strips about a metre wide, pull each strip off the gripper strips around the edge of the room, then lift the underlay and pry up the gripper strips and staples. A bedroom is a manageable afternoon job with a utility knife, pliers and a flat bar. Wear thick gloves: the pins on gripper strips are sharp.
Below are the tools you need, the steps in order, what to do on stairs, what you might find underneath, and how to get rid of the old carpet once it is up.
Tools and safety gear
You do not need anything specialised. Most of this is already in a garage toolbox.
- Heavy work gloves. Gripper strips have rows of angled pins that cut skin easily.
- Utility knife with spare blades. Carpet backing blunts a blade fast, so change it often.
- Pliers. For gripping the carpet corner and pulling staples.
- Flat bar or pry bar and a hammer. For lifting gripper strips and door trims.
- Knee pads and a dust mask. Years of fine dust sit under old carpet and come up with it.
- Duct tape and a screwdriver. Tape keeps the rolls tight, and the screwdriver takes off metal door bars.
Clear the room first. Take any doors that swing over the carpet off their hinges if they will get in the way.
How to remove carpet, step by step
- Take off the door trims. Unscrew or lever up the metal bars at each doorway where the carpet meets another floor.
- Start in a corner. Grab the carpet with pliers and pull it up off the gripper strip. Once a corner is free, you can get your hands under it.
- Pull it back along one wall. Work along the edge until a strip of carpet about a metre wide is loose.
- Cut it into strips. Fold the loose carpet back and cut through the backing from the underside. A metre-wide strip rolls up small enough to carry out on your own.
- Roll and tape each strip. Roll it tight with the pile facing in, then tape it.
- Repeat across the room. Seams joined with tape will pull apart or can be cut along the join.
Cut on top of the underlay, never on a timber floor you might want to keep. A blade that goes through the backing will also score the boards.

Lifting the underlay, staples and gripper strips
With the carpet out, the room is down to the underlay. How it comes up depends on the floor below.
On a timber or particleboard floor, underlay is usually stapled down. Pull it up in sections, then go over the whole floor with pliers or a staple lifter. A single staple left behind will show through a thin new floor.
On a concrete slab it may be loose, or glued in patches. Old rubber underlay can break down over the years and stick to the floor. On one of our jobs at The Ponds, the old underlay had fused to the sheet floor and came away in strips, so it was scraped back by hand.
Gripper strips come last. Slide the flat bar under each strip next to a nail and lever it up a little at a time. On timber they are nailed. On concrete they may be nailed or glued, and the glue leaves a ridge that needs scraping off.
Put lifted gripper strips straight into a box, pins down. They are easy to tread on.
Removing carpet from stairs
Stairs take longer than a room of the same size. Each step has its own gripper strip at the back of the tread, and the carpet is usually stapled under the lip of each nosing as well.

Start at the top step and work down. Pull the carpet off the top gripper, then cut it across every few steps so you are never wrestling one long piece. Work slowly around balusters. Then go back up and pull every staple from each tread and riser.
On our Kellyville job the stair carpet came up and the subfloor was already level, so the new floor went straight on with no prep.
What you might find under the carpet
Lifting carpet tells you what your subfloor is. That decides what can go down next.
| What is underneath | Where it is common | What usually happens next |
|---|---|---|
| Concrete slab | Apartments, ground floors, most newer houses | Scrape off glue and underlay, fill cracks, level any dips |
| Particleboard sheeting | Upper floors of newer timber-framed houses | Pull staples, sand proud sheet joins, re-screw loose sheets |
| Hardwood floorboards | Older houses and cottages | Pull staples and tacks, re-fix loose boards |
| Old vinyl, lino or floor tiles | Older kitchens, halls and units | Leave alone until checked (see below) |
Our post on what a subfloor is and how to prepare one goes through each type and how flat it needs to be for different floors.
Found old vinyl or lino? Stop there
If your home was built or renovated before 1990, old sheet vinyl, lino or vinyl floor tiles hidden under the carpet could contain asbestos. You cannot tell by looking.
Leave it where it is. Do not sand, scrape, drill or break it up. Have a sample tested first, and if it does contain asbestos, its removal is a job for a licensed contractor.
Carpet and underlay on their own are not the concern here. It is the older hard flooring that sometimes sits beneath them.
How to get rid of old carpet
Old carpet is heavy and bulky, and it will not fit in a household bin. There are three usual routes in Sydney.
- Council bulky waste collection. Most councils run one, with limits on how much they take and how it must be rolled and tied. Check your council's website before you put it out.
- A skip bin. Easiest for a whole house. Tell the hire company it is carpet and underlay, as some bins have rules on what goes in.
- A waste transfer station. You take it there yourself and pay by the load.
Keep the gripper strips separate and boxed. Nobody collecting the rolls should have to handle loose pins.
Doing it yourself or leaving it to the installers
Pulling up carpet is a fair DIY job if the new floor is going down later. It saves a step on install day, and you see the subfloor before anyone quotes on prep.
Some people would rather not. If we are laying your new floor, removal of the old carpet is priced at the free measure along with any stairs and slab work, once someone has seen the room. Our regular installers then lift it as part of the job.

Replacing carpet with carpet? Our guide to how much carpet costs sets out supply prices per m2. Going to a hard floor instead? Browse our hybrid flooring, which floats over a prepared slab or sheet floor.
Ready to price the new floor, removal included? Book a free measure and quote anywhere in Sydney, for homes and commercial premises.
Tags:
Share:

